The SilverStone Strider Platinum ST1000-PT & ST1200-PT PSU Review: Tenured
by E. Fylladitakis on May 4, 2018 9:00 AM EST- Posted in
- Cases/Cooling/PSUs
- PSUs
- SilverStone
- 80Plus Platinum
SilverStone Strider Platinum 1000W & 1200W - Hot Test Results
Enhance is an OEM who does not get concerned with power quality when the figures are good enough and these two units are no exception. The voltage ripple figures are mediocre, with the 3.3V/5V voltage lines flirting with the 50 mV recommended design limit.
SilverStone ST1000-PT Main Output | ||||||||
Load (Watts) | 202.7 W | 505.92 W | 752.48 W | 997.17 W | ||||
Load (Percent) | 20.27% | 50.59% | 75.25% | 99.72% | ||||
Amperes | Volts | Amperes | Volts | Amperes | Volts | Amperes | Volts | |
3.3 V | 2.29 | 3.36 | 5.72 | 3.36 | 8.58 | 3.33 | 11.44 | 3.32 |
5 V | 2.01 | 5.06 | 5.04 | 5.06 | 7.55 | 5 | 10.07 | 5 |
12 V | 15.2 | 12.16 | 37.99 | 12.14 | 56.99 | 12.04 | 75.99 | 11.96 |
Line | Regulation (20% to 100% load) |
Voltage Ripple (mV) | |||||
20% Load | 50% Load | 75% Load | 100% Load | CL1 12V |
CL2 3.3V + 5V |
||
3.3V | 1.2% | 16 | 30 | 36 | 48 | 20 | 42 |
5V | 1.2% | 20 | 24 | 30 | 44 | 20 | 40 |
12V | 1.6% | 18 | 26 | 40 | 56 | 54 | 36 |
The 12V lines hold better, with the ST1000-PT and the ST1200-PT reaching up to 56 mV and 50 mV at maximum load respectively, which is half of the 120 mV recommended design limit but still considerably higher than what the competition nowadays offers. Voltage regulation is good and similar for both units, at about 1% for the 3.3V/5V lines and 1.6% for the 12V line across the nominal load range.
SilverStone ST1200-PT - Main Output | ||||||||
Load (Watts) | 243.59 W | 608.13 W | 902.73 W | 1197.78 W | ||||
Load (Percent) | 20.3% | 50.68% | 75.23% | 99.82% | ||||
Amperes | Volts | Amperes | Volts | Amperes | Volts | Amperes | Volts | |
3.3 V | 2.31 | 3.35 | 5.79 | 3.34 | 8.68 | 3.33 | 11.57 | 3.32 |
5 V | 2.04 | 5.1 | 5.09 | 5.09 | 7.64 | 5.05 | 10.18 | 5.04 |
12 V | 18.51 | 12.18 | 46.29 | 12.16 | 69.43 | 12.03 | 92.57 | 11.97 |
Line | Regulation (20% to 100% load) |
Voltage Ripple (mV) | |||||
20% Load | 50% Load | 75% Load | 100% Load | CL1 12V |
CL2 3.3V + 5V |
||
3.3V | 1.1% | 16 | 28 | 36 | 44 | 20 | 38 |
5V | 1.15% | 18 | 20 | 30 | 42 | 20 | 44 |
12V | 1.7% | 16 | 22 | 34 | 50 | 50 | 38 |
High ambient temperatures have a small but measurable effect on the energy conversion efficiency of the Strider Platinum units. The average conversion efficiency of the two units drops by about 0.6%, to 91.4% and 91.6% for the ST1000-PT and the ST1200-PT respectively, which is very good considering the very large difference in ambient temperature. This hints that the components that the manufacturer is using are capable of maintaining high performance at higher temperatures and/or significantly oversized for their tasks.
Regardless of the high ambient temperature, both units disabled their fans when the load was very low but would immediately speed up their fans when the load increased above just 100 Watts. The two units were not really louder compared to our room temperature tests, meaning that they were already running their fans at maximum speed before, even though the internal temperatures were much lower than the >80°C figures we get inside our hotbox.
21 Comments
View All Comments
Samus - Saturday, May 5, 2018 - link
I'm still rocking an 11 year old PCP&C 750 Quad. 80 Plus something or other rating. I think it was rated 80 Plus before there were even sub-categories of 80 Plus.notashill - Tuesday, May 8, 2018 - link
I had the same PSU but it died (for the second time, first was under warranty and it was repaired not replaced) about a year and a half ago. Still not a bad service life.DanNeely - Tuesday, May 8, 2018 - link
That was a very good supply in its day, and is probably fine to keep using in whatever you've got it in for as long as you keep it. I'd be hesitant to install it in a new built system today though.I can't find any reviews that did a cross load test on it; but from its age it's almost certainly a design with separate 12V and 3.3/5V segments whose voltages get out of spec if you put a huge load one of them and barely anything on the second (aka cross load).
That's an issue because modern systems use 12V almost exclusively and put very little load on the 3.3/5V rail (PCIe cards can draw up to 10W@3.3V, a few years ago AMD was to get the most power out of the slot, nvidia was limiting itself to the 65W available at 12V; USB draws 5V for most uses, 2.5/3.5" drives might tap 5V, but almost never touch the 3.3V line because of molex to sata adapters that leave it unpowered); which puts older PSUs into a cross load situation if you're running GPUs and load the 12V rail heavily. Newer designs avoided this by going pure 12V at the AC-DC conversion step and then making lower voltages via DC-DC conversion.
Achaios - Friday, May 4, 2018 - link
"considering that the ST1000-PT was struggling to reach the 80Plus Platinum certification limits"@E.F: You should know, since you are a PSU specialist, that Silverstone has got a history of marketing units made by Enhance, which fail to meet the Certification limits or barely make it.
Case in point, my own Silverstone Strider Gold 850W. This unit fails to meet the Gold Certification by 1-2 %. This is a year 2011 PSU and the reviewer who first noted the fact was Johnny Guru.
After, what, 7 years Silverstone learned nothing from the negative publicity and they just keep doing the same thing. Ofc such data does not concern the average buyer out there who buy PSU's b/c of attractive packaging or good price, just us enthusiasts.
Silverstone sells good, solid units, just not without flaws and not the best-of-the-best. I'd label them Tier 2 or Tier 3.
stanleyipkiss - Friday, May 4, 2018 - link
Who is Tier 1 then?praeses - Friday, May 4, 2018 - link
Seasonicpraeses - Friday, May 4, 2018 - link
... and probably FSP Group after them.Fallen Kell - Friday, May 4, 2018 - link
Tier 1 is Seasonic, FSP, Corsair, and Enermax who design (and in the case of Enermax build) their own power supplies. Many of the other ones simply use an OEM design, possibly with a few modifications, but in many cases it is simply an OEM with specific paint/color scheme, or specific cables, etc..praeses - Friday, May 4, 2018 - link
Corsair is usually Seasonic or FSP. I'm not sure that I would put Enermax in the same tier as Seasonic/FSP.piroroadkill - Monday, May 7, 2018 - link
As far as I recall, Corsair uses Great Wall for a good number of their mid-range units, and Flextronics at the very high end.